Rhopoint Nordic News


pressure transducers with fast in-media temperature sensor

0.02% accurate pressure transducers with fast in-media temperature sensor

The 311-38-540 pressure and temperature combination sensor incorporates a temperature sensor which is immersed in the direct media stream to detect rapid changes in media temperature. In many other pressure transducers ,which have an internal temperature sensor, this temperture device is located inside the sensor body, meaning that the response time is increased. More...


IL613 IL614

100Mbps in three channels

The IL613 and IL614 are three channel passive input digital signal isolators with CMOS outputs capable of data rates to 100Mbps. They have a similar interface but better performance and higher package density than optocouplers. The devices are manufactured using patented (GMR) technology for small size, high speed, and low power. More...


CANned Pressure

With standard pressure ranges to 15,000 PSI, this new range of CANBus transducers is ideal for high cycle and high pressure applications such as those found in the toughest sub-sea, industrial, automation, military and automotive environments.. More...



High current zero ohm jumpers

The SMT-0 ( 100A ) and SMK-0 ( 50A ) zero ohm jumpers are designed for high current applications. Many zero ohm jumpers can only carry a small amount of current before they fail. These high current devices are suitable for many power applications such as: Motor speed controllers, power supplies and automotive applications. More...



0.9V pinch-off voltage low noise high gain JFET

The IFND89 is a new n-channel JFET transistor with integrated back to back input over voltage protection diodes.
The device offers the designer a unique combination of low noise ( 6.8nV/√Hz typ. ) high gain device combined with a low pinch-off voltage of less than 0.9V.
The internal back to back diodes provide over voltage protection. More...


High power, high precision shunt resistors

High power, high precision shunt resistors

The new range of high precision high power shunt resistors, now available from Rhopoint Components is ideal for battery testing during manufacture. At present the series comprises nine models with current ranges from 150A to 1000A. All models supply 100mV at full current rating. The voltage output is available via a Kelvin connected flying lead, which enables a resistance tolerance of between 0.1% and 0.5%. More...


Low power angle sensor

2.5mm² low power angle sensor

Developed using Tunneling Magnetoresistance (TMR) technology the new AAT001-10E angle sensor has been developed for applications such as: rotary encoders, motor shaft and knob position sensors. The sensor is made up of an array of four TMR elements rotated at 90 degree intervals and connected in a bridge configuration. The output represents the sine and cosine functions of the magnetic field applied to the sensor. When this magnetic field is rotated above the sensor the outputs can be used to determine the resultant angle with an accuracy within 3°.More...


Isolated profibus interface

Single chip 40Mbps isolated Profibus interface

The new IL3685 galvanically isolated interface enables designers to have a fully Profibus compliant design while at the same time simplifying PCB layout and reducing component count when compared to a traditional opto isolator based circuit. Designed using patented IsoLoop Giant Magnetoresistance (GMR) technology, this high-speed differential bus transceiver is designed for bidirectional data communication on balanced transmission lines and can achieve a data rate of up to 40Mbps.More...


GMR current sensor

GMR non contact current measurement

Ideal for low current detection, the new AAV003-10E is a highly linear, extremely low hysteresis GMR (Giant Magneto Resistance ) current sensor with an on-chip current strap. A GMR bridge sensor element close to the strap senses the current. The output of the bridge voltage is bipolar and proportional to the current through the strap over a -80 to +80 mA input range.More...


RTD chip sensor

1206 RTD sensors

Available in both 100ohms and 1000ohms the CPT temperature sensors are specifically designed to offer board level temperature sensing and compensation over the wide temperature range of -50°C to 150°C. These sensors are manufactured using a thin film layer of platinum which gives a linear temperature / resistance dependance.

Both class A and class B accuracy devices are available and they conform to DIN EN 60751.More...